Pixhawk 4 Autopilot Flight Controller


  • A new and small form factor
  • More computing power and 2X the RAM than previous versions
  • New sensors with higher temperature stability
  • Integrated vibrations isolation
  • Increased ease-of-use: pre-installed with most recent PX4 (v1.7)
  • Additional ports for better integration and expansion
  • Ship From:China
    Dispatch:Ship between 2 bussiness days
    Payment Methods:Paypal & Credit Cards and more >Buyer Protection:
    Full Refund ,If you do not receive your order
    Full or Partial Refund , If the item is not as described more >payment


    Recommended for You


    HolyBro Pixhawk 4 Autopilot Flight Controller & M8N GPS Module Combo

    Pixhawk4 Quick Start Guide

    Pixhawk 4 Pinout

    GPS Quick Start Guide

    Power Management Board Quick Start Guide

    Pixhawk 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro
    and the PX4 team optimized to run the full Dronecode stack and comes preinstalled with the latest PX4 firmware (v1.7).

    Specification: ( Manual)
    Brand Name: HolyBro
    Item Name: Pixhawk 4 Flight Controller & M8N GPS Combo
    Version: Plastic Case / Aluminum Case ( Optional)
    Dimensions: 44x84x12mm
    Weight: 15.8g
    Diffirence of them:
    Mainly points at the Pixhawk 4 Flight Controller’s Case.

    Technical Specification
    Main FMU Processor: STM32F765
    (32 Bit Arm®Cortex®-M7, 216MHz, 2MB memory, 512KB RAM )
    IO Processor: STM32F100
    (32 Bit Arm® Cortex®-M3, 24MHz, 8KB SRAM )
    Accel/Gyro: ICM-20689
    Accel/Gyro: BMI055
    Mag: IST8310
    Barometer: MS5611
    GPS: M8N GPS/GLONASS receiver;
    integrated magnetometer IST8310

    Electrical data
    Power Module Output: 4.9~5.5V
    Max Input Voltage: 6V
    Max Current Sensing: 120A
    USB Power Input: 4.75~5.25V
    Servo Rail Input: 0~36V

    ●8-16 PWM servo outputs (8 from IO, 8 from FMU)
    ●3 dedicated PWM/Capture inputs on FMU
    ●Dedicated R/C input for CPPM
    ●Dedicated R/C input for Spektrum / DSM and S.Bus with analog / PWM RSSI input
    ●Dedicated S.Bus servo output
    ●5 general purpose serial ports
    – 2 with full flow control
    – 1 with separate 1.5A current limit
    ●3 I2C ports
    ●4 SPI buses
    -1 internal high speed SPI sensor bus with 4 chip selects and 6 DRDYs
    – 1 internal low noise SPI bus dedicated for Barometer with 2 chip selects, no DRDYs
    ●1 internal SPI bus dedicated for FRAM
    ● Supports dedicated SPI calibration EEPROM located on sensor module
    ●1 external SPI buses
    ●Up to 2 CANBuses for dual CAN with serial ESC
    – Each CANBus has individual silent controls or ESC RX-MUX control
    ●Analog inputs for voltage / current of 2 batteries
    ●2 additional analog inputs

    Environmental data, quality & reliability
    Operating temp. ~40~85C
    Storage temp. -40~85C

    Package Included:
    1x Pixhawk 4 Flight Controller ( Plastic Case Or Aluminum Case )
    1x GPS Module
    1x Power Management Board *1
    1x I2C splitter Board
    3x 6 to 6 pin cable (power)
    2x 4 to 4 pin cable (CAN)
    1x 6 to 4 pin cable (Data)
    2x 10 to 10 pin cable (PWM)
    1x 8 to 8 pin cable(AUX)
    1x PPM/SBUS out cable
    1x XSR receiver cable
    1x DSMX receiver cable
    1x SBUS receiver cable
    1x USB cable *1
    1x ‘X’type folding pedestal mount
    2x 70mm & 140mm carbon rod stand off
    1x 6*3 2.54mm pitch Horizontal Pin
    1x 8*3 2.54mm pitch Horizontal Pin
    1x Foam Set


    There are no reviews yet.

    Be the first to review “Pixhawk 4 Autopilot Flight Controller”

    Payment Methods:


    2.Credit Cards
    Know more payment methods,[click here]!

    Shipping Methods:

    When you place your order at rcbuying,we will choose the right shipping mothods to ship the package to you,such as EMS,DHL,UPS,Fedex,China airpost and others,know more [click here]

    New Arrivals